Hitec ECLIPSE 7 Pdf User Manuals. View online or download Hitec ECLIPSE 7 Owner’s Manual. View and Download HITEC Eclipse 7 Pro user manual online. 7 Channel GHz Aircraft Radio Control System. Eclipse 7 Pro Remote Control pdf manual. Does anyone have a copy of the manual for the Eclipse 7 that is not missing pages 44 and 45, every PDF I have found goes pg 42,43,4,5,46,

Author: Majar Samudal
Country: Albania
Language: English (Spanish)
Genre: Photos
Published (Last): 13 January 2007
Pages: 270
PDF File Size: 11.41 Mb
ePub File Size: 6.1 Mb
ISBN: 553-9-52418-936-6
Downloads: 19534
Price: Free* [*Free Regsitration Required]
Uploader: Zunos

If you have a nearby slope, practice flying on very light lift days, where you can just barely keep the model airborne. Gimbals Feel the silky smooth action of the new four ball bearing supported gimbals in the Eclipse 7 Pro. Aircraft Flight Trimming Chart The following chart may be used to systematically set up and trim a model manua straight flight and aerobatic maneuvers.

Glid Model Data Recording Sheet Rest – Data Reset Page 9 Set-up Use of the Hitec 2. The Model Select ware version of Eclipse 7 Pro.

These functions are used to select the model memory, the model type from airplanes, gliders, and helicoptersset the Timer, and other useful functions. Gimbals Feel the silky smooth action of the new four ball bearing supported gimbals in the Eclipse 7 Pro.

Swah – Swashplate Adjust Page 62 Menu Descriptions – Helicopter The Throttle Hold function moves the engine throttle servo to a selected position near idle, and disengages manuwl from the throttle stick. Reverse the sign in front of the percentage with ecoipse Data 1. This function is turned on with the Flt. Switch transmitter power OFF. If all the servos tilt the swash aft with up elevator stick, go to the next step.

  FLEGEL MELINDA J PRIMEIROS SOCORROS NO ESPORTE PDF

HITEC Eclipse 7 Pro User Manual

The aileron dual rate switch is located over the right-hand stick; the elevator dual rate switch is located over the left-hand stick, and the rudder dual rate switch is to the right of the elevator switch. Range Check Function It is critical that before each flight session you perform a range check that confirms the signal between the receiver and transmitter is appropriate. Functions relating specifically to gliders and helicopters may be found in the following sections.

Mode switch turns this function on and off fully back turns it ON.

Page 12 Set-up Use of the Hitec 2. Helicopter Flight Trimming Chart We encourage you to review this information before using these products. Connect the right elevon to receiver CH1 The slower the model flies, the more mixing is needed, Elevator Operation and the left elevon to CH2. Both batteries in both the Instructor and Student Transmitters should be properly charged and installed when flying in the trainer mode.

For this reason it is possible to have low sensitivity at low stick angles like dual ratesand yet have full motion at full stick deflection. Rvmx – Revolution Mixing See the THCV menu description on page 58 for more details.

Glider Model Function Descriptions your sailplane. Page 51 Glider Model Function Descriptions 6. You can change the curve values to make a steeper curve near idle and shallower curve past hover.

Page 7 Hitec 2. Glider Model Function Descriptions to the sailplane trimming chart on page 51 for more details. Aircraft Flight Trimming Chart The following chart may be used to systematically set up and trim a model for straight flight and aerobatic maneuvers. Table of Contents Add to my manuals Add.

  EVERMOTION ARCHMODELS 56 PDF

Changing The Eclipse 7 Transmitter’s Mode Charging The Eclipse 7 Ni-cd Batteries Comments to this Manuals Your Name. Now you may set up mannual throw for the elevator, but gain more drag than penetration ability.

Manual do usuário HITEC ECLIPSE 7 – Baixe o seu guia ou manual de usuário HITEC ECLIPSE 7

Page 25 Model Setup Functions 4. If the student’s transmitter has aremovable RF module, remove it from the transmitter.

Transmitter Input Buttons The buttons are used for different things as follows: These new gimbals were created to give you the smoothest action demanded by the highest performance aircraft. Page 7 If any of your servos are located too far away to plug directly into the receiver like the aileron servoor you need to unplug the servo each time you disassemble the model, use a servo extension cord to extend the length of the servo lead.

Exponential [ Exp] Switch power back on. With the transmitter switched off, turn on your Flashing ec,ipse while pressing both of the two Edit keys the two keys on the far left.