ASTM D Pull Off Test Standard – Free download as PDF File .pdf), Text File .txt) or read online for free. ASTM D and BS EN ISO describe several different test apparatus; The tensile pull-off method for adhesion testing, as outlined in ASTM D and . ASTM A/AM Steel, Sheet and Strip, Heavy-Thickness Coils, Hot- Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy.

Author: Tushura JoJomuro
Country: Montenegro
Language: English (Spanish)
Genre: Spiritual
Published (Last): 16 December 2018
Pages: 393
PDF File Size: 9.66 Mb
ePub File Size: 9.56 Mb
ISBN: 458-7-53460-796-8
Downloads: 61048
Price: Free* [*Free Regsitration Required]
Uploader: Sataur

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Results obtained by each test method may give different results. The moment new editions of the standards you monitor are released, changes are made, or appendixes are published, you will be alerted by email.

Pull-off strength of coatings from concrete is described in Test Method D Fracture will occur along the weakest plane within the system comprised of the test fixture, glue, coating system, and substrate, and will be exposed by the fracture surface. Note 2—Method A, asm appeared in previous versions of this standard, has been eliminated as its main use is for testing on concrete substrates see Test Method D Webprint Printed and bound.

Results should only be assessed for each test method and not be compared with other instruments. Aetm test method is applicable to x portable apparatus meeting the requirements for determining the pull-off strength of a coating in this standard see Annexes.

Results should only be assessed for each test method and not be compared with other instruments. This service is not 09f1 if you are a URL user where you do not log in with an email address. asfm

ASTM D – 09E1 PDF

Aetm obtained by each test method may give different results. Combining values from the two systems may result in non-conformance with the standard. Pull-off strength of coatings from concrete is described in Test Method D Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

They are capable of applying a concentric load and counter load to a single surface so that coatings can astk tested even though only one side is accessible. Failure will occur along the aastm plane within the system comprised of the test fixture, adhesive, coating system, and substrate, and will be exposed by the fracture surface.

  DECLARATIA 394 PDF

Note 2—Method A, which appeared in previous versions of this standard, has been eliminated as its main use is for testing on concrete substrates see Test Method D Standards 091 is d free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

This test method serves as a means for uniformly preparing and testing coated surfaces, and evaluating and reporting the results. This test method serves as a means for uniformly preparing and testing coated surfaces, and evaluating and reporting the results. They are capable of applying a concentric load and counter load to a single surface so that coatings can be tested even though only one side is accessible.

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. This asgm method is applicable to any portable apparatus meeting the requirements for determining the pull-off strength of 009e1 coating in this standard see Annexes.

The procedure in this standard was developed for use on flat surfaces.

There are five instrument types, identified as Test Methods B-F. Combining values from the two systems may result in non-conformance with the standard.

ASTM D4541 – 09E1 PDF

This test method maximizes tensile stress as compared to the shear stress applied by other methods, such as scratch or knife adhesion, and results may not be comparable. Therefore, when a series of results will be compared with one another or used for statistical analysis, the type of apparatus, substrate, test procedures, glue type, and if scoring is used should be the same for the pulls considered. The procedure in this standard was developed for use on flat surfaces.

Active view current version of standard. Failure will occur along the weakest plane within the system comprised of the test fixture, adhesive, coating system, and substrate, and will be exposed by the fracture surface. This includes change in glue, load fixture size, substrate coating cure time, pull rate, environmental conditions, if the coating is scored, or using a different device.

A web subscription provides an easy and secure access to standards, and you are guaranteed to always have the latest edition. Results obtained by each test method may give 09d1 results. Note 1—The procedure in this standard was developed for metal substrates, but may be appropriate for other rigid substrates such as plastic and wood. Historical Version s — view previous versions of standard.

  HD74LS76AP DATASHEET PDF

Link to Active This link will always route to the current Active version of the standard. This test method maximizes tensile stress as compared to the shear stress applied by other methods, such as scratch or knife adhesion, and results may not be comparable.

Depending on the radius of the surface, the results could have greater variability with lower values and averages.

Method A, which appeared in previous versions of this standard, has been eliminated as its f use is for testing on concrete substrates see Test Method D It is the responsibility of the user of this standard to e1 appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.

Depending on the radius of the surface, the results could have greater variability with lower values and averages. Pull-off strength of coatings satm concrete is described in Test Method D The procedure d this standard was developed for metal substrates, but may be appropriate for other rigid substrates such as plastic and wood.

It is imperative to identify the test method used when reporting results. The values given in parentheses are for information only.

Active view current version of standard Translated Standard: Link to Active This link will always route to the current Active version of the standard. This includes change in glue, load fixture size, substrate coating cure time, pull rate, environmental conditions, if the coating is scored, or using a different device. Method A, which appeared in previous versions of this standard, has been eliminated as its main use is for testing on concrete substrates see Test Method D This ensures that you are always up-to-date and saves you both time and money.

Historical Version s – view previous versions of standard. Link to Active This link will always route to the current Active version of the standard.