ASTM Gradel, JIS Grade, TIA, RMI 25, TIMETAL 35A, ST Sheet and plate. ASTM B Gr1, Mil-T CP Bars and billets. ASTM B Gr1. Tube. ASTM B Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality Titanium Plates, Sheets & Coils, Titanium sheets & plates.

Author: Arashikasa Barisar
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Environment
Published (Last): 18 April 2004
Pages: 116
PDF File Size: 2.28 Mb
ePub File Size: 1.71 Mb
ISBN: 708-8-83490-792-1
Downloads: 54667
Price: Free* [*Free Regsitration Required]
Uploader: JoJotilar

Titanium Plates, Sheets & Coils

A number in parentheses indicates b26 year of last reapproval. This standard has been approved for use by agencies of the Department of Defense. The chemical analysis shall be conducted by the standard b2665 normally utilized by the b625 and purchaser.

The bend specimen may be of less than full material thickness; however, the outer surface of the specimen must include the original material surface with no material removal or surface conditioning other than at the rounded corners, and must otherwise be representative of the product as supplied.

Alternate Yield Strength Maximum S2. B — 10 Standard Specication for Titanium and Titanium Alloy Strip, Sheet, and Plate1 This standard is issued under the xed designation B; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

The surface of the specimen must include the original material surface with no material removal or surface conditioning, except corners may be rounded to a maximum radius of 0. The percentage of titanium is determined by difference. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

  LOO RIEGELMAN METHOD PDF

Only original conforming test results or the conforming retest results shall be reported to the purchaser. If the results for the retest fail to conform to the specication, the material will be rejected in accordance with Section Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

If shipped as descaled, sandblasted, or ground, the manufacturer shall be permitted to remove minor surface imperfections by spot grinding if such grinding does not reduce the thickness of the material below the minimum permitted by the tolerance for the thickness ordered.

The bend shall be made on a radius equal to that shown in Table 1 for the applicable grade. Specied thickness was corrected from 0.

Grade 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use.

Bend tests are not applicable to material over 0. This is in accordance with the round-off method of Practice E NOTE 2—If the longer dimension is under 36 in. Wstm 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use.

Marking and Packaging Specimens shall be taken from sheet or astmm material produced from the same ingot or bloom materials, processed the same way to the same nominal thickness, width and length, produced in one production run or campaign, nished in the same way, and otherwise representative of the material supplied.

This abstract is a brief summary of the referenced standard. Special Flatness Requirements S3. Unalloyed titanium plus 0. Originally approved in ast, E The purchaser may, in the written purchase order, request analysis for specic elements not listed in this specication.

The characters shall be not less than 38 in. Last previous edition approved in as B — 09a1.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Heat numbers shall occur at least 3 times across the width of the sheet and at intervals not greater than 2 ft 0. Grades 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use. MPa In widths over 16 to in. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.

  ERVING GOFFMAN INTERNADOS PDF

For plates of irregular shape, the over thickness tolerances apply to the greatest width corresponding to the width ranges shown.

ASTM B _图文_百度文库

Other industry standard methods may be used where the ASTM test methods in atsm. ASTM International takes no position respecting the validity ast any patent rights asserted in connection with any item mentioned in this standard. When the straight edge is placed on a single high point, the maximum deviation from the plate at each end shall be no greater than 0.

The grades of titanium and titanium alloy metal covered by this specification shall have the chemical composition requirements of: NOTE 4—The maximum deviation from a at surface does not customarily exceed the tabular tolerance for the longer dimension specied.

E For Grades 5, 6 and 32 the elongation on materials under 0.

The report shall include results of all chemical analysis, tensile tests, and all other tests required by the specication. Ingot hydrogen need not be reported. Mechanical properties for conditions other than annealed or plate thickness over 1 in.